C1946 Seat Track Position Switch Circuit Open- Causes & Fix

C1946 Seat Track Position Switch Circuit Open.

Causes of the C1946 code

• Faulty Switch for Seat Track Position
• The harness for the Seat
• Track Position Switch is open or shorted.
• Poor electrical connection in the Seat
• Track Position Switch circuit.

How can I repair the code C1946? Look over the list of “Possible Causes” above. Examine the connected wire harness and connections visually. Look for broken, bent, pushed out, or corroded connection pins as well as damaged components.

Mechanic Cost for diagnosing C1946 code:

1.0 The C1946 code costs 1.0 hour of effort to diagnose. The cost of auto repair labor varies depending on your region, vehicle make and model, and even engine type. The majority of vehicle repair firms charge $75 to $150 per hour.

What are the symptoms of the C1946 code?

The engine light is illuminated (or the Service Engine Soon Warning Light is on).

Description of the C1946 code The Seat Track Position Switch is monitored by the Engine Control Module (ECM). When the Seat Track Position Switch does not meet factory requirements, the ECM sets the OBDII code.

OBD Code C1946.

Description and symptoms of the OBD/2 C1946 error code.

The fuel pressure sensor is in the range, yet it is low. The FRP pressure is monitored by the complete component monitor (CCM) for safe fuel pressure. When the fuel pressure goes below a predetermined level, the test fails. Fuel pressure is low. FRP sensor that has been damaged Circuit with too much resistance Fuel is scarce or non-existent. A failure is indicated by a FRP PID value of less than 551 kpa (80 psi). Fuel is scarce or non-existent. A failure is indicated by a FRP PID value greater than 896 kpa (130 psi).

At this stage, we’re presuming the fuses and relays are in excellent working order. Using your car information source, find the PCM/TCM and the power input signal circuit. Remove the connector from the PCM/TCM, turn on the ignition, and use the positive test lead of the DVOM to probe the relevant circuit.

Repairing the C1946 Error Code:

The open check engine light on a c1946 seat track position switch circuit is possibly the most perplexing of lights because it might imply a variety of problems, from not tightening the gas cap enough to looking out for pistons shooting through the hood and into the sky. Connecting your car to a scan tool is the simplest approach to figure out what this light is telling you. The C1946 error code diagnostic gadget resembles an enlarged calculator and connects to the car’s communication connection. After you tell it to do the scan, it communicates with your car’s computers to figure out what’s causing the light to illuminate.

OBD2 Code C1946: Common Causes

The failure of C1946 Seat Track Position Switch Circuit Open is a typical cause of code C1946, however there are various alternative possibilities, such as;

• Low oil pressure causes erratic camshaft position.

• Faulty Solenoid Valve for Intake Valve Timing Control

• Leaks in the exhaust system.

• The wrong gasoline filler cap was utilized.

Related: 6 Common Symptoms of a Bad Catalytic Converter

Chassis Trouble Code C1946

One of the most annoying challenges that technicians confront is diagnosing chassis sounds. Fortunately, noise, vibration, and harshness (NVH) diagnostic techniques and equipment have been developed to pinpoint the source of the noise.

For other automobiles, use the C1946 code.

You can see the C1946 DTC for your specific automobile model. To see obd2 solutions, we picked various models to view.

C1946 FORD-Seat Track Position Switch Circuit Open

The FORD code C1946 might have a variety of causes.

• Incorrect track position of the seat.

• Adjust the location of the seat track Either the switch harness is broken or it is shorted.

• The Seat’s Track Position The switch circuit has a bad electrical connection.

Related: How Much Does Repainting a Bumper Cover Cost?

What is the best way to fix the FORD code C1946?

Look over the “Possible Causes” section. Examine the associated wire harness and connections visually. Look for connecting pins that are broken, bent, pushed out, or rusted, as well as damaged components.

The expense of determining the cause of FORD code C1946.

The diagnostic time for the C1946 FORD code is 1.0 hour. Labor expenses for auto repairs vary depending on your region, automobile make and model, and even engine type. The majority of vehicle repair firms charge $75 to $150 per hour.

What are the FORD C1946 code’s indicators and symptoms?

The engine light is turned on (or the Service Engine Soon Warning Light is on).

The FORD code C1946 is described in detail.

The Engine Control Module keeps an eye on the Seat Track Position Switch (ECM). The ECM sets the OBDII code when the Seat Track Position Switch fails to match manufacturer specifications.

C1946 LEXUS Code-(Signal From Steering Control ECU To Front Active Stabilizer Control ECU Is Malfunctioning)

The LEXUS code C1946 might be for a variety of reasons.

• Faulty Front Active Stabilizer Control ECU; • Faulty Front Active Stabilizer Control ECU harness; • Faulty Front Active Stabilizer Control ECU circuit

How can I fix the LEXUS error code C1946?

Examine the “Possible Causes” section above. Visually inspect the attached wire harness and connectors. Look for connecting pins that are broken, bent, pushed out, or rusted, as well as damaged components.

Related: Car Running Hot But Not Overheating [FIX]

The cost of diagnosing the C1946 LEXUS code is as follows:

The time it takes to diagnose the C1946 LEXUS code is 1.0 hour. Auto repair labor costs differ based on your location, car make and model, and even engine type. The bulk of auto repair shops bill between $75 and $150 per hour.

What are the signs and symptoms of the LEXUS C1946 code?

The Anti-Lock Braking System (ABS) is a braking system that prevents the (ABS) ON THE WARNING LIGHT is a braking system that prevents the (ABS) ON THE WARNING LIGHT is a braking system that prevents the (ABS) ON THE W

The engine light has been switched on (or Service Engine Soon Warning Light)

C1946 is an LEXUS code with a description.

The Active Stabilizer Suspension System uses CAN communication to gather data for control operations. When another system fails, the Diagnostic Trouble Code (DTC) is kept.

Related: Can A Coolant Leak Drop Oil Pressure?

C1946 LINCOLN Code-The circuit for the seat track position switch is open

The C1946 LINCOLN code has several possible reasons.

Seat Track Position Faulty Switch Position of the Seat Track Either the switch harness is broken or it is shorted.

The Seat Track’s Location The switch circuit has a bad electrical connection.

How do I fix the C1946 LINCOLN code?

Examine the “Possible Causes” section above. Visually inspect the attached wire harness and connectors. Look for connecting pins that are broken, bent, pushed out, or rusted, as well as damaged components.

The cost of diagnosing the C1946 LINCOLN code is as follows:

The diagnosis of the C1946 LINCOLN code takes one hour. Auto repair labor costs differ based on your location, car make and model, and even engine type. The bulk of auto repair shops bill between $75 and $150 per hour.

Related: Noise when Braking at Low Speed [100% Fix]

What are the C1946 LINCOLN code symptoms?

The engine light is turned on (or the Service Engine Soon Warning Light is on).

C1946 is the LINCOLN code description.

The Engine Control Module keeps an eye on the Seat Track Position Switch (ECM). The ECM sets the OBDII code when the Seat Track Position Switch fails to match manufacturer specifications.

C1946 MERCURY Code-The circuit for the seat track position switch is open

• Seat Track Position Switch harness is exposed or shorted • Faulty Seat Track Position Switch • Bad electrical connection in the Seat Track Position Switch circuit Potential reasons of the C1946 MERCURY code

Related: “Check Engine Light” Car is not Accelerating

How can I fix the MERCURY error code C1946?

Examine the “Possible Causes” section above. Visually inspect the attached wire harness and connectors. Look for connecting pins that are broken, bent, pushed out, or rusted, as well as damaged components.

The following are the costs associated with diagnosing the C1946 MERCURY code:

The diagnosis of the C1946 MERCURY code takes one hour. Auto repair labor costs differ based on your location, car make and model, and even engine type. The bulk of auto repair shops bill between $75 and $150 per hour.

What are the signs and symptoms of the MERCURY code C1946?

The engine light is turned on (or the Service Engine Soon Warning Light is on).

The C1946 MERCURY code is described below.

The Engine Control Module keeps an eye on the Seat Track Position Switch (ECM). The ECM sets the OBDII code when the Seat Track Position Switch fails to match manufacturer specifications.

C1946 TOYOTA Code-Signal from the steering control ECU to the front active stabilizer control ECU is faulty.

The TOYOTA code C1946 might be for a variety of reasons.

The Front Active Stabilizer Control ECU is broken.

Front-end Control of the Active Stabilizer Either the ECU harness is exposed or it is shorted.

A faulty electrical connection exists in the ECU circuit for Front Active Stabilizer Control.

What is the best way to fix the TOYOTA code C1946?

Examine the “Possible Causes” section above. Visually inspect the attached wire harness and connectors. Look for connecting pins that are broken, bent, pushed out, or rusted, as well as damaged components.

The price of analyzing the TOYOTA code C1946.

The C1946 TOYOTA code requires 1.0 hour of labor to troubleshoot. Auto repair labor costs differ based on your location, car make and model, and even engine type. The bulk of auto repair shops bill between $75 and $150 per hour.

What are the signs and symptoms of the TOYOTA C1946 code?

The warning light for the Anti-Lock Braking System (ABS) is illuminated. The engine light is turned on (or the Service Engine Soon Warning Light is on).

C1946 TOYOTA code description

The Active Stabilizer Suspension System uses CAN communication to gather data for control operations. When another system fails, the Diagnostic Trouble Code (DTC) is kept. The circuit for the seat track position switch is open (C1946 FORD Code).

Disclaimer:

The content on this website is meant only for general information purpose and does not and shall not be construed as any solicitation, procurement, display, aggregation, marketing or advertisement of products. AutoLawNow.com is not an intermediary and hence does not endorse or solicit any such products. The information on this website is derived from publicly available sources and AutoLawNow.com cannot verify or confirm the genuineness, truth, veracity or authenticity of this information.

Display of any trademarks, tradenames, logos and other subject matters of intellectual property belong to their respective intellectual property owners. Display of such IP along with the related product information does not imply AutoLawNow.com ‘s partnership with the owner of the Intellectual Property or issuer/manufacturer of such products.