4l60e Transmission Control Module Location | 4l60e TCM Location | 4l60e Speed Sensor Location

4l60e Transmission Control Module Location | 4l60e TCM Location | 4l60e Speed Sensor Location

In a 4l60e transmission, the transmission control module is usually found on the back of the transmission case, under the cover. It’s located below the engine control module. Depending on the vehicle model, it may also be situated near the battery or center console within the vehicle.

Make sure read on carefully below to understand the 4l60e Transmission Control Module that shall help you for troubleshooting 4l60e TCM.

Transmission specifications for the 4L60e transmission.

The GM 4L60E is an advancement of the Turbo-Hydramatic 700R4, and it replaced the tried-and-true TH350. Lower gear ratios, improved valve body, addition of fourth gear (overdrive), and a lockup torque converter make it a popular choice for street performance or retrofitting 400-700 HP depending on year and internal modifications, making it a popular choice for street performance or retrofitting 400-700 HP depending on year and internal modifications.

Specs for the 4L60E and 4L65E.

4L60E / 4L65E Specs
Weight146 lbs. (dry).
CaseCast Aluminum.
Max Torque: 360 lb ft (488 N.m).
Fluid Capacity8.4 quarts (9.64″ torque converter) or 11.4 quarts (11.81″ torque converter).
Engine Compatibility90 degree “small and big block” I6, V6, and V8.

Gear Ratios

1st Gear3.059
2nd Gear1.625
3rd Gear1.00
4th Gear0.696
Reverse Gear2.299

Are you fed up with your Chevy‘s transmission?

Changing a transmission is a common occurrence. Getting anything new is usually an exciting experience. As a result, you’ll receive an automatic transmission. Don’t assume it needs to be an emergency – think about how to reset chevrolet trans module and enjoy some surprises from our experts before making any judgments. They’ve prepared two quick and easy methods for this: turning the ignition on and off ten times or detaching and reconnecting battery cables in four minutes while starting the engine with the key out (this needs effort). This process can assist if your automobile is slow while driving owing to a malfunctioning controller unit, which can also create issues such as extended downshifts during acceleration.


Chevy Where is Transmission Control Module Located

Toyota is Working on a Fake Manual Transmission for Electric Cars (EV’s)

4l60e tcm location-reset
4l60e tcm location-reset

Resetting the Transmission Control Module in Steps

1. The first step is to change the key position.

Checking the key position is one of the last tasks before resetting a transmission control module. To begin, alter it from 2 to 1 and then back to 2 for confirmation. Check that your dashboard lights are on in this phase as well, since they will switch off briefly throughout these processes, so don’t do anything else while you’re checking things out, such as stepping on the accelerator or starting your automobile engine! When shifting positions, you should hear two clicks at the same time – be sure you don’t miss them if you want excellent results after all this effort.

Step 2: Activate the gas pedal.

It’s time to put your right foot on the accelerator pedal once you’ve completed the previous step. Make sure you complete this motion all the way down, not halfway, because doing so will trigger a kick-down switch, which might result in unfavorable outcomes. Continue pushing until you reach Step 2.

Step 3: Continue to wait.

Don’t worry if you’ve come here to reset the gearbox control module on your Chevy. During this time, all you have to do is stay for around 15 seconds and depress the accelerator pedal, which will be enough to get the accelerator pedal working again after a full reset procedure.

Step 4: Remove the key from the ignition.

You must return to the key after putting your foot on the accelerator pedal for roughly 10-12 seconds. Do not, however, let off of the pedal. Remember how I turned it all the way up before? Now we must restart the process of turning them off so that they do not become trapped in this posture! All you have to do is turn them off with both hands – or just one if you’re a multitasker– and then return them to their original position: 0 mph (zero). Make careful nothing strange occurs during our next stop once you’ve turned these keys over again, since those rocks may seriously damage us.

Related:  Charging System Failure in A Car [Causes & 100% Fix]

Related: Rear Tail Light Cover Replacement Cost [Rates 2022]

Step 5: Let go of the gas pedal.

Always remember to maintain both feet on the pedals while starting your automobile. When turning off the key and setting it in the home position, you can release one foot from its pedal, but only if there is no risk of your foot slipping or being hit by a rapid stop.

When starting out in traffic, never leave either foot unattended since many accidents are caused by distracted drivers who let go just as their vehicle was about to collide with another driver’s automobile approaching them head-on into an intersection.

Step 6: Remain patient.

We understand that you don’t want to be kept waiting. The restart procedure, on the other hand, takes some time and demands patience on your part! You must give your Chevy a break after stepping off the gas pedal, much like we do when we step off an escalator. Check that the ignition key is in the off position and that it is not moved. Please use caution when following these instructions; removing the battery may cause automobile issues that may necessitate expert assistance (this may cost both money and precious time).

Related: How Much Does a Headlight Cover Replacement Cost? (2022)

Step 7: You’re all set.

You’re almost through with the operation. You’ve already completed a large amount of work on your car, but you’re not quite ready to drive it yet! The engine and transmission parts still need time to finish their programming, so don’t rush this phase while deciding whether or not to do something else while they program themselves into one smooth running machine.

When that’s done, all that’s left is for you to drive about town to let the TCU and ECU systems get a feel for how well you manage your car on your own—after that, there’ll be nothing keeping them from operating properly alongside each other without any interference.

4l60e transmission control module location
4l60e transmission control module location


The newest model 4l60-E gearbox’s hood, main body, and rear cover are all constructed of cast aluminum alloy.

GM shortened the length of the box to 21.9 inches, which is the same as a 15.4 inch package. Manual transmission, with increased efficiency for fuel consumption over time that is comparable to smaller engines while maintaining high torque output when you need it most, thanks to its 30 slots on input shafts and an automatic cooling system that uses square oil reservoirs on their left side rather than right like other transmissions.

Any GM enthusiast should have the 4L60E automatic transmission since it is cutting-edge and powerful. The 6 hex bolts on every 4L60E model from 1997 to 2006 are a key characteristic that distinguishes it from its predecessors before 1997 and after 2006.

The C/K Truck, Sonoma Jimmy Tahoe Yukon Astro Safari Suburban Silverado Bravada Firebird Camaro Corvette, and other notable models are compatible with this car, making it a must-have for any aspiring auto enthusiast.

Next What (4L60E Transmission Control Module)

We already walked you through the process to install a contemporary electronically-shifted 4L60E gearbox in your third-gen. However, we’ve only gotten you halfway there.

Electronically controlled transmissions, which employ a computer to command the transmission when, when, and how to shift, have improved the performance and longevity of GM overdrive units dramatically. You won’t have to deal with the irritation of your transmission shifting into overdrive too early or too late with a computer in charge.

TCI has gone one step further by allowing the end user to fine-tune their trans via a simple software interface and a computer (TCI recently launched a stand-alone sensor module that allows you to program the TCU once it has been set up with your PC). The TCU application lets you to adjust several elements of your transmission’s behavior with a laptop computer after completing a simple step-by-step setup procedure, including converter lock-up, shift points, and line pressure.

Because the majority of this installation requires wire and computer input, it’s better to leave it to a professional if you’re not familiar with crimping and cutting, or even basic PC operations.

Related:  Indian Scout Bobber – Review, Comparison, Drawbacks & Key Points

After that, we needed to find a secure location to mount the TCU. Because the device is waterproof, it may be installed in the engine compartment. If you’re dealing with a late-model emissions car like our ’83, this isn’t a probable choice because there’s hardly enough place for everything that’s already in there.

We needed to get the harness through the floor to its connector on the transmission now that we knew where we were going to put it. On the passenger side, we identified a position beneath the shift console that was out of sight and didn’t interfere with the seat mounting. We used a hole saw from beneath to make an aperture large enough for the main connector after drilling a pilot hole from inside the automobile. We ran the inside section of the harness under the carpet towards the dash, where the TCU would be installed, once the harness was buttoned up on the bottom.

The TCU must know the throttle position at all times in order to identify the correct shift points and stiffness. TCI sells a remote-mount TPS (PN 377401 $152.60) for cars without a TPS. A Distributor Adapter Harness (PN 377100 $51.80) and TPS Adapter Harness (PN 377201 $80.40) that links the TCU connections into your current GM harness are also available to make things easier under the hood.

The torque converter lock-up release switch (gray wire) is attached to the positive brake light wire on the driver’s side of the automobile. When the brakes are applied, this unlocks the converter, allowing for smoother deceleration. We were left with simply the 5-foot long communication connection that allows the TCU to communicate with a laptop after reinstalling the ECM and TCU beneath the dash.

The TCU has an electrical switch that may be used to manually shift the transmission. The paddle shifters are convenient and easy to use, and they easily plug into the harness. It may also hold two distinct programs, either of which can be selected via an externally mounted switch. For instance, one software for commuting and another to play a neck-snapping strip music. You also have the option of completely turning off your overdrive or locking and unlocking your converter.

Related: Car Won’t Start After Oil Change | 100 % Fix & Causes

Often Asked Questions-4l60e Transmission Control Module Location.

Q) What causes a TCM (4l60e Transmission Control Module Location) go bad?

The most typical causes of transmission control module damage are as follows:

1. An excessive amount of voltage.

2. There is a short circuit in the circuits.

3. A short circuit exists in the actuator or solenoid circuits.

4. A shortcircuit is caused by water in the circuitry. To mention a few, vibration and/or temperature stress.

Q) What are the signs and symptoms of a 4L60E transmission control module (TCM) failure?

The 10 most typical symptoms of a malfunctioning transmission control module are listed below.

1. Unpredictable repositioning.

2. Problems with shifting at higher speeds.

3. Downshifting problems

4. A shift that is postponed.

5. There is a lack of fuel economy.

6. The gearbox does not shift gears while it is not moving.

7. As you accelerate, the transmission does not upshift.

8. The transmission is stuck in first or neutral.

9. I’m not going to change gears.

Q) When the Check Engine Light comes on, it means that something is wrong with the vehicle. Is it possible for a malfunctioning TCM to generate a code?

Your car’s TCM may be faulty, or one of your transmission components may be defective, according to your ODB-II scanner.

An open transmission fluid temperature circuit is indicated by the P0613 code, whereas a transmission control system is indicated by the P0700 code. If codes such as P0706 and ETC display on the screen, it’s most likely due to a wiring or programming issue.

Q) Yes, I discovered that my Transmission Control Module (TCM) was defective after using this fantastic program, and everything is now OK. Is programming a TCM required?

If a generation and transmission control module is fitted, it must be programmed. This must be done in your car or with an approved automated system that can wirelessly transfer data back to the user’s PC through Bluetooth.

Automatic transmissions are far more responsive than manual gearboxes because they employ electrically lubricated gears rather than oil-lubricated gears. You shouldn’t have to maintain the automobile again if you’ve already changed the TCM.

Related:  How Long Does An Alignment Take? [Actual Info]

Q) What is the price of a TCM replacement?

If your car requires a new gearbox control module, you could expect to pay around $700 for materials and between $500 and 1000 for labor.

This varies based on where they are and whether the work is being done as part of an installation or as a replacement. There are other internet firms that sell TCMs for rates ranging from free to several hundred dollars, with follow-up shipment included, if you don’t mind getting into the nitty gritty.

Q) What does it signify when TCM contact is lost?

The trouble code U0101 develops when communication with the transmission control module (TCM) is lost. When a TCM does not receive or transmit a response across the CAN bus, this code is shown, and it indicates one of two scenarios:

The battery in your car might be nearly dead or malfunctioning, suggesting an issue with the computer system. A failure may occur if anything disturbs signals supplied through Ethernet cable utilizing the TCP/IP protocol.

Q) What is the method for resetting the TCM on a Chevy?

My car has a complex machine that requires numerous steps to start. One of the first things I do when my engine starts acting up is to reset the TCM by turning on the ignition, pressing hard on the accelerator pedal for 10 seconds, shutting off everything so that all lights turn off at their own time, and then waiting patiently for 5 minutes before restarting.

Q) What are the steps to resetting the Chevy ECM?

Using a socket wrench or wrench, remove the negative battery cable nut. Disconnect the battery cord and set it aside to prevent electrical discharge from injuring other components of your vehicle. Turn on the headlights for at least 10 minutes to drain power from the ECM (electronic control module). Turn off the headlight switch once you’ve finished emptying the gasoline pump’s memory.

If the battery is removed, TCM will be reset.

The default settings of a TCM cannot be restored by removing the battery. You’ll need to use a transmission scan procedure to do so, and simply disconnecting the terminals won’t address the problem with gear shift troubles.

Q) What is the time frame for reprogramming a transmission control module?

Having a computer in our home is rather common in today’s environment. But what exactly is going on with all of these circuits and chips? So, here’s what I’m about to say! To begin, there are three primary components: hardware (the physical machine), firmware (a set of instructions generated by someone else that tells your PCM chip how to run), and software (a set of instructions written by someone else that tells your PCM chip how to operate)

Reprogramming takes 30 to 40 minutes on average, but programming takes ten times as long since computers need time to not only store data on hard drives, but also to transfer that data to the memory chip, where it can be accessed quickly when required later.

Conclusion-4l60e Transmission Control Module

You won’t get weary of the same gearbox now that you know how to reset the transmission control module! Our experts’ answer is really straightforward. All you have to do now is remember the warnings and follow these directions attentively. It will take around 10 minutes to finish, and everything should operate well for the following 15 minutes as long as there are no more engine problems while driving about town. I hope you found this information on “How To Reset Transmission Control Module For Chevy” helpful; if you have any questions, please post them in the comments section below.


The content on this website is meant only for general information purpose and does not and shall not be construed as any solicitation, procurement, display, aggregation, marketing or advertisement of products. AutoLawNow.com is not an intermediary and hence does not endorse or solicit any such products. The information on this website is derived from publicly available sources and AutoLawNow.com cannot verify or confirm the genuineness, truth, veracity or authenticity of this information.

Display of any trademarks, tradenames, logos and other subject matters of intellectual property belong to their respective intellectual property owners. Display of such IP along with the related product information does not imply AutoLawNow.com ‘s partnership with the owner of the Intellectual Property or issuer/manufacturer of such products.

About autolawnow

Check Also

Chevy 5.3 Vs 6.2 Engine [Which Chevy is Reliable?]

Chevy 5.3 Vs 6.2 Engine [Which Chevy is Reliable?]

Chevy 5.3 Vs 6.2 Engine: The small-block V-8 engine has been used in race cars, …

Leave a Reply

Your email address will not be published. Required fields are marked *